One of the most common problems with a Maytag washing machine is a malfunctioning lid switch, the most common problem on all washing machines. Damon Koch has years of writing experience ranging from software manuals to song lyrics. In extreme cases the washer's belt and/or motor pulley can be damaged as a result. This machine has only been used for about 4 months :( Contractor's Assistant: Thanks. If the door lock is defective, the washer door will not latch properly. Inspect the door latch for damage. To determine if the door lock has failed electrically, use a multimeter to test each of the door lock switches for continuity. We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need. Email. I have a Maytag Centennial Washer and the lid is locked. If the door lock is defective, the washer door will not latch properly. If the door lock is damaged, replace it. The washer's drive pulley can become loose and slip down causing a loud, fast ticking sound whenever the motor is running. Already ordered? If the door latch is damaged, replace it. Grasp the front of the washer opening with one hand and the back of the cabinet with the other and pull the cabinet forward about 6 inches. It is not a terribly difficult repair but the part required is costly. The door lock assembly might be defective. The lid latch has been a sore spot on this washer type. Snap the wiring harness into the new lid switch and secure it in place with the two screws. The door latch assembly might be defective. Unplug the Maytag washer's electrical cord from the wall outlet. Reassemble the cabinet by reversing the steps you used to disassemble it.

The washer's lid strike attached to the lid can also swell with rust and not properly operate the lock. A loose pulley sounds something like this... Sound Description: Fast agitation function, slow agitation function, then spin function. It was on spin cycle when the power went out, when the power came back on both the green and red lights were flashing with the lid locked.

Hold times are long. He also has worked in building maintenance since 2004. The door strike is not repairable—if it is broken, you must replace it.

The lid switch interrupts the operation of the machine when it is open and allows normal operations when it is closed. Step 2 Unscrew the screws on the sides of the control panel. I see this is a common problem/complaint. Hunker may earn compensation through affiliate links in this story.

12,087 satisfied customers. Start doing it yourself with the confidence that comes with 100+ years of experience. You should see the lid switch and have access to it. The main control board may be defective. otherwise we'll assume you're okay to continue.

Unfortunately doesn't help me since it is Christmas Eve and impossible to get anyone to come look at it. If the door lock is damaged or does not latch properly, replace it. Learn how to adjust your settings. Scan the included wiring diagram until you find the wires labelled “lid switch” and “lock switch.” The majority of washing machine lid lock switches are powered by 3 or 4 wires, each of which performs a different function. Inspect the door lock for damage. If none of these parts are defective, consider replacing the main control board.

and the washer will not start or run properly.

Inspect the door lock for damage. Use a Philips screwdriver to remove the two screws that secure the switch to the washer. Unfasten the screws on either side of the top of the cabinet with a 5/16-inch nut driver. This site uses cookies to improve your experience. Before replacing the main control board, first check all of the components of the lock mechanism. Enter model number to search for the required part specific to your product, Browse our parts categories to select from a variety of parts for your product. Flip the control panel up and out of the way. 99 If you catch it early, simply add some thread lock onto the pulley nut and tighten it back on. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. Shipping all 7 days! In most cases the washer will basically work normally except for a horrible noise when the washer is washing or spinning. The lid latch has been a sore spot on this washer type. Over time and with use, the switch can wear out. Slide a putty knife under the control panel on each side to release the spring clips. Join Repair Clinic's VIP email list for 10% off, plus other discounts and tips! 01 - Door Lock Motor and Switch Assembly. Hopefully, these will be color-coded. Inspect the door strike assembly for damage. Maytag Washer door or lid won't lock. If the washtub bounces or feels particularly soft you may need to replace the suspension kit. Unscrew the screws on the sides of the control panel. Step 1 Unplug the Maytag washer's electrical cord from the wall outlet. This washer sensor problem usually will show up in the form of a fault code like F7E1, F7E5, or F7E7.

The spring portion of these tub suspension rods have been known to become soft and allow the tub to bounce, leading to the washer regularly going off balance and banging the inside of the washer during spin. If there are screws, remove them with a Phillips screwdriver. Once the washer door is closed, the washer can begin operating. He has attended Lorain County Community College as well as Cleveland State University. Even a novice can replace the lid switch on a Maytag washer in about half an hour. Not as common as some other washer issues, but much more costly is a bad center bearing. The Maytag Centennial washer's tub is suspended on 4 suspension rods located on the outer corners of the washer's tub.

W10240513 Washer Lid Latch Lock Strike, Replace Part # AP4514459 1873013 AH2579805 EA2579805 PS2579805, Replacement Part Fits for Whirlpool, Kenmore, Amana, Maytag Roper, Sears 5.0 out of 5 stars 1 $9.99 $ 9 . Tech/owner. Once the washer door is closed, the washer can begin operating. By creating an account you agree to the Hunker. Washing Machine Door Lock Motor and Switch Assembly. The Centennial washer's drum should quickly jump back to it's original position and stop when released and not bounce. Important Notice:

MTW Maytag Centennial Model Washer Repair Guide. Flip the control panel up and out of the way. Loud, even, grinding with tub movement are commonly caused by a bad bearing that is inside the gearcase. Common solutions for: Maytag Washer door or lid won't lock. The door lock secures the washer door shut during operation. The washer's lid strike attached to the lid can also swell with rust and not properly operate the lock.