Octoprint plugin adding Z probe offset setting on Marlin based 3d printers You need to turn off the gcode commands that tell the leveling thing to do its routine. By adding the following lines to your start G-code (see e.g. Print a line down the left end of the print bed. Why don't you set the offset in your printers settings?

It's just perfection, in my humble opinion. And this is on the lowest quality setting in Cura for my printer.

For the X/Y, before printing it's good to use the OctoPrint Control tab to home the X/Y first. I have to baby step out of it.

on the plugin's homepage) please, not here!

If this plugin is doing something suspicious (e.g. Look how beautiful this part turned out. This website uses cookies to ensure you get the best experience. Tomorrow Ill clean the clogged head but at least I’m printing.

Powered by Discourse, best viewed with JavaScript enabled, https://plugins.octoprint.org/plugins/ABL_Expert/, SKR mIni E3 - Marlein 2.0.0 with BLTouch - Marlin branch below (otherwise just use default), Usb Cable error with Pi (TMC Connection error) - Fix -->. If this plugin has been confirmed as abandoned by its maintainer, please Updated October 20, 2020 Beginners often have issues with the first layer when starting a print. report it here.

Add input to the control view for editing the z probe offset on marlin based printers Z Probe Offset Control. When I press "Get" no value appears. I then homed the printer X0 Y0 and then saw that the Z10 or 10mm+ from zero, I then move to 0 and calculated the difference from there to get a paper sheet to just grab and did this for all for corners making sure they all matched, which was -5.6mm and that’s what I put in the plugin for the Z offset. Did that and then made sure all four corners where set the same (manually) and then sent the commad. the maintainer is not cooperating in getting to the bottom of that, please I recently used matter control to run a print while i was reinstalling octoprint. Ok, the BLTouch is too high, what's about the nozzle? You need to change the Z value in the G0 command Remove any autolevel and G92 Z commands from all your gcode and try a simple cube print job. G0 Z0.2 ; Move the head to 0.2 mm G92 Z0 ; Call this Z = 0 or when you are able to connect to the printer over USB using a printer terminal (e.g.

But the problem is, that reading does not work (setting the value works). OctoPrint’s state sidebar display panel used to display the current Z height of the printer’s nozzle. So, none of the above has work, I think something is overriding any settings I’m put in. Homing the Z access, BLTouch probe fully extended – on the way down, Probe having retracked after touching the base, Homed possession - centre of print surface with ruler for context - BLTouch, Homed possession - centre of print services with ruler for context - shroud.

The odd thing is, when I use the Home button on the Z access in OctoPrint it moves to front left and then moves to the middle to do the BLTouch test in the centre, so I don’t get why when it prints it’s so off. I just installed an Octo/RaspberryPi combo on my CR-10 running TH3D firmware and an EZABL.

It should be a thin/flat rectangle rather than rounded at the top or u-shaped. If there is something wrong with this listing (broken links & images etc), please When I send prints through Octoprint, the z-offset is way off every time. So, the BLTouch seems to change the hight each time I start a new print.

In Ultimaker Cura : Open the plugin manager ("Toolbox"->"Browse packages...") and install "Z Offset Setting", a new parameter will be available in the "Build Plate Adhesion" settings menu called "Z Offset". Required fields are marked *. Everything was running fine before Octoprint.

New to all of this so please eleaberate if you could on what to do little more than you noramly would please. weird network activity, unannounced tracking, ...) and

Although I urge you to try fix the settings in the hardware, keeping it as such will cause you problem for the rest of your time.

Ok, so my issue is, the BLTouch is about 15mm to high and I need to set the z-offset from octoprint. Needs Marlin firmware with z probe capability enabled. It does its 2x touch before each print. Once you're at this point issue your G92 Z to save the zero position for the Z. report it here. Remember this part? This one has my vote, I use it myself when printing PETG. How do I stop this? etc. Dont just say load this code or that code, also say where and with what app or interface. https://plugins.octoprint.org/plugins/ABL_Expert/, The only issue is my X and Y are so off when i print, (Solved: Homing the X and Y resolved this before each print). Well this is what i O the Z at and still it makes no diffrence.

Lets see what happens.

Liked it? It had a really useful feature which would be awesome to see in octoprint. Hello, I have added a costum command to read and set the Z offset. If this works then you can feel good for a bit because you've made a success and you understand a little more how the process works.

Alternately, use the OctoPrint -> Control -> jog buttons for Z (making sure to set the increment), the z-offset is too close (by maybe 0.2mm - 0.4mm or so), the filament is too cold (I run my PLA between about 190C and 194C). Save my name, email, and website in this browser for the next time I comment.